JORC Type OPTIMUM / OPTIMUM-HP-S Electronic Timer Condensate Drain Solenoid Valve

JORC Type OPTIMUM / OPTIMUM-HP-S Electronic Timer Condensate Drain Solenoid Valve

The JORC Type OPTIMUM electronic drain valve is matched with the solenoid valve by the analog circuit solid-state electronic timer to realize the automatic discharge of the condensed water of the compressed air system. Electronic drain valves are widely used in compressed air system components such as filters, separators, dryers, gas storage tanks, and drip feet. The discharge time and interval can be adjusted according to different needs.
Features:
1. One model is suitable for all applications, easy to install, fully automatic, maintenance free.
2. Interval and discharge time are adjustable and have test buttons.
3. A variety of voltages, a variety of interfaces are available.
4. 4.5mm large diameter direct acting valve, fluoro rubber seal.
5. Equipped with a ball valve filter, separated from the drain valve.

Technical parameter of JORC Type OPTIMUM Electronic Timer Drain Solenoid Valve:

Filter display of Jorc type timer controlled condensate drain electronic valve:

Working display of Optimum Type Timer Controlled Drain Electromagnetic Valve:

Split type or Combined type JORC type time drain solenoid valve for you to choose:

More details about OPTIMUM Electronic Timer Condensate Drain in below Youtube Video:

Check the working condition of the electronic drain valve:

It is recommended that you check the working condition of the electronic drain valve by pressing the manual test button test on the timer each time you check the compressed air system.

Proceed as follows:
1) Close the isolation ball valve and press the test button to ensure that the electronic drain valve is isolated from the air pressure system (at zero pressure)

2) Cut off the drain valve power supply.

3) Remove the coil (the electronic drain valve must be de-energized before the coil is removed, otherwise the energized coil will burn out after it leaves the valve body), disassemble the solenoid valve, take out the valve plug and spring, and flush the valve body and spool with water. And the spring, and then re-installed, the fault can be eliminated.

In the process of using the electronic drain valve, the following points should be noted:
1. Before installing the drain valve, it is preferred to remove sludge, copper scrap, rust, etc. from the compressed air system. It is recommended to drain the system for 3-5 minutes at full pressure before installing the drain valve.

2. The direction of drainage is the same as the direction of the arrow on the valve body.

3. The supply voltage should match the drain valve voltage (the drain valve voltage is marked on the coil). Do not connect the wrong power supply.

4. The test membrane switch on the timer is a manual test button. Each time the button is pressed, the drain valve is discharged once. This button is used to check the drainage condition at any time in daily work.

5. The two knobs of the timer are used to adjust the discharge and interval time. The user should adjust the time according to the climate and working conditions.

6. In addition to the connection function, the small screws on the drain valve junction box have the function of pressing the seal to prevent water from entering the timer and the coil, so be sure to tighten. Otherwise, the gasket will not be waterproof, which will cause the coil. And the burning of the timer. The lock nut of the terminal is also waterproof, so be sure to tighten.

7. When the electronic drain valve is in use, the solenoid valve may not be tightly closed, which is always leaking. Usually the fault is not caused by the quality of the drain valve itself. The reason is that the condensate is too dirty, and the tiny solid particles in it Enter the valve plug and get the spool stuck.

Welcome to your any question and inquiry!

* Foucus on your demand, Offer you best solutions as the first mission of Ningbo Brando Hardware Co., Ltd, we work on designing and manufacturing solenoid coils, solenoid armatures and solenoid valves for more than 15 years.   * We have served customers from Europe, North America, Middle east, Southeast Asian by designing and manufacturing for their automation fluid control applications, related to industries of pneumatic automation equipment, food beverage dispenser, agricultural irrigation, printing and dyeing, dust collector, home appliance, automobile, textile, refrigeration, etc.

* Since the company's inception, we are dedicated to providing high quality products and service to our customers. With focusing on our customers' demands, at before production we discuss technical points according to applications with customers to reduce mistake and save cost for both sides. During production, we use high precision CNC machine, machining center to control dimensions and improve productivity. At beginning and mid of machining, our senior inspectors check quality regularly by recording data on documents as per ISO9001 management system. Before shipment, our staff make testing and complete inspection one piece by one piece to ensure the products without defect when reached our customer's hands.

* Ningbo Brando Hardware Co., Ltd will offer you best service with fast response, let's make the fluid control application more widely and smartly.

Product Categories:

1. Solenoid Valve
2. Solenoid Coil
3. Solenoid Armature
4. Solenoid Coil Connector
5. Solenoid Valve Timer
6. Pulse Valve
7. Valve Diaphragm
8. Pulse Controller
9. Refrigeration Valve
10. Pneumatic Valve
11. Pneumatic Fitting
12. Pneumatic Cylinder
13. Pneumatic Filter Regulator Lubricator
14. Pneumatic Vibrator
15. Ball Valve
16. Butterfly Valve
15. and so on