Ingersoll Rand Air Compressor Doosan PRO-TEC Ponti Oil 36899706 / 36899714

Ingersoll Rand Air Compressor Doosan PRO-TEC Ponti Oil 36899706 / 36899714

Ingersoll-Rand its part number : 36899706 (old) / 36899706 (new)

Ingersoll Rand PRO-TEC Ponti Oil can normally work in ultra-low temperature; may be at an ambient temperature

of -40 degrees to 52 degrees, can withstand working pressures up to 200PSI; at ambient temperatures from -40

degrees to 18 degrees can withstand working pressures up 350PSI. Designed for high pressure type design; at

operating temperature is between -23 degrees to 52 degrees, working pressure 350PSI more. Pro-Tec (Bao Tai

Yau) applies pressure 300PSI following models, XHP505 for high pressure 300PSI these and other specific

circumstances (such as low temperature). PRO-TEC Ponti oil.

Bao Thai Oil ( 36899706,36899714 )

Ingersoll PRO-TEC oil Ponti main features :

In ultra-low temperature under normal operating synthetics ; ambient temperature of -40 degrees to 52

degrees, can withstand working pressures up to 200PSI; ambient temperature of -40 degrees to 18 degrees,

can withstand working pressures up to 350PSI.

Designed for high pressure type design ; operating temperature is between -23 degrees to 52 degrees ,

working pressure 350PSI more.

Pro-Tec ( Bao Tai Yau ) applies pressure 300PSI following models , XHP505 for high pressure 300PSI these and

other specific circumstances ( such as low temperature ) .

PRO-TEC Po Thai Oil Part Number : 36899706 (5gallon) Applicable models : VHP750/MHP825/HP900/P425E

Item

Typical data

" Ponti "

XHP605

Performance500

Kinematic viscosity (40 ℃), mm2 / s

36

65.2

29.4

Kinematic viscosity (100 ℃), mm2 / s

7.5

10.4

5.8

Viscosity Index

163

147

136

Freezing Point , ℃ (F)

-43 ( -45 )

-48 ( -55 )

-54 ( -65 )

Flash point ( open ), ℃ (F)

188 ( 370 )

227 ( 440 )

216 ( 240 )

Corrosion (T2Cu, 100 ℃, 3h), level

1b

1b

1b

Proportion

0.869

0.858

0.838

Ingersoll-Rand air compressor cooling oil :

Name

Part Number

Applicable models ( see filling port )

Mineral oil

99262842/42868976 (15KG)

VHP400/P600/VHP750E/P950E and other older models

Doosan Pro-TEC Compressor Fluid

SECTION 1 COMPOSITION/INFORMATION ONINGREDIENTS
Chemical Names and Synonyms: Severe Treat Min. Oils & Additives
Ingredients Considered Hazardous to Health:
This product is not formulated to contain ingredients, which have exposure limits established by U.S.
agencies. It is not hazardous to health as defined by the European Union Dangerous
Substances/Preparations Directives.

SECTION 2 HAZARDS IDENTIFICAT-parts-partsION
US OSHA Hazard CommuniCAT-parts-partsion Standard: Product assessed in accordance with OSHA 29 CFR
1910.1200 and determined not to be hazardous.
Emergency Response Data: Slightly Hazy Amber Liquid. DOT ERG no. -NA

SECTION 3 FIRST AID MEASURES
Eye Contact: Flush thoroughly with water. If irritation occurs, call a physician.
Skin Contact: Wash contact areas with soap and water.
Inhalation: Not expected to be a problem.
Ingestion: Not expected to be a problem. However, if greater than ½ liter (pint) ingested, seek medical
attention.

SECTION 4 FIRE-FIGHTING MEASURES
Special Fire Fighting Procedures: Water or foam may cause frothing. Use water to keep fire exposed
containers cool. Water spray may be used to flush spills away from exposure. Prevent runoff from fire control
or dilution from entering streams, sewers, or drinking water supply.
Special Protective Equipment: For fires in enclosed areas, fire fighters must use self-contained breathing
apparatus.
Flammable limits – LEL: NA, UEL: NA.
NFPA Hazard ID: Health: 0, Flammability:1, Reactivity: 0
Hazardous Composition Products: Metal oxides. Carbon monoxide.

SECTION 5 ENVIRONMENTAL AND DISPOSAL INFORMATION
Steps to be Taken in Case of Spills: Soak up with suitable absorbent material, and then sweep into plastic
bag for disposal.
Waste Disposal Method: Dispose in accordance with local, state, or federal regulations.

SECTION 6 HANDLING AND STORAGE
Handling: No special precautions are necessary beyond normal good hygiene practices.
Storage: Do not store in open or unlabelled containers. Store away from strong oxidizing agents or
combustible material.

SECTION 7 EXPOSURE CONTROLS/PERSONAL PROTECTION
Eye Protection: Normal industrial eye protection practices should be employed.
Skin Protection: No special equipment required. However, good personal hygiene practices should always
be followed.
Exposure Limits: This product does not contain any components which have recognized exposure limits.
However, an exposure limit of 5.00 mg/m3 is suggested for oil mist.

SECTION 8
Typical physical properties are given below. Consult Product Data Sheet for specific details.
Appearance: Liquid
Color: Slightly Hazy Amber
Odor: Mild
Odor Threshold-ppm: NE
pH: NA
Boiling Point C(F): >316 (600)
Melting Point C(F): NA
Flash Point C(F): >175 (347) (ASTM D-92)
Flammability: NE
Auto Flammability: NE
Explosive Properties: NA
Oxidizing Properties: NA
Vapor Pressure –mmHg 20 c: < 0.1
Vapor Density: > 2.0
Evaporation Rate: NE
Relative Density, 15/4 C: 0.87
Solubility in Water: Negligible
Partition Coefficient: > 3.5
Viscosity at 40 C, cSt: 40.0
Viscosity at 100 C, cSt: 7.4
Pour Point C(F): -40 (-40)
Freezing Point C(F): NE
Volatile organic Compound: <8.00 (Wt. %); 0.574 lbs/gal
DMSO Extract, IP-346 (WT.%): < 3, for mineral oil only
NA=NOT APPLICABLE NE=NOT ESTABLISHED D=DECOMPOSES

SECTION 9 STABILITY AND REACTIVITY
Stability(THERMAL, LIGHT, ETC.): Stable.

Since establishment in 1985, Guangdong ALI Testing Equipment Co., Ltd, a wholly-owned subsidiary of GSKA Group has been providing a wide and complete range of products and services to the society. GSKA has now 16 offices, warehouses and service centres in China, with head office loCAT-partsed in Hong Kong. There are more than 100 employees in GSKA Group, and we are expanding into many industries with rapid expanding pace of China.

There are mainly 4 departments in GSKA Group, namely:

1) Construction and Mining equipment

GSKA has been cooperating with many international famous brands in China, such as Ingersoll-rand, Atlas Copco and Liebherr. Our products include concrete batching plants, concrete mixers, hydraulic crawler drills, pneumatic crawler drills, water well drills, air compressors, road compactors, breakers and various other equipment. We are major in several industries, such as hydro-electric power plants, cement quarries, coal mines and railway systems.

In order to provide a quick response to our customers, we have stocked over US$1.5 Million spare parts of Ingersoll-rand and Atlas Copco in our Chinese warehouse. Recently, we have exported small air compressors, pneumatic crawler drills, water well drills and drilling accessories and spare parts to overseas market.

2) Power Group

GSKA has been supplying CAT-parts and Broadcrown gensets for more than 15 years. Our major customers include Telecoms, Banks, Airports, Factories and many other sectors in the society. We are also doing assembly of gensets in China, under our brand name of "GSKA " with ratings from 1KVA to 2000KVA. The quality of "GSKA " genset has won a very good reputation from customers in China and overseas market.

We are also the specialists for genuine spare parts, such as CAT-parts, Perkins, FG Wilson, Cummins, , Volvo, etc.

Besides gensets, we also provide total solution on the power problems, such as Powerware - UPS, DC system and battery ,lightning equipment and many other electronic products.

3) Security and IT Group

GSKA acquired famous USA brand name Locktronix in 2004 and started manufacture electric locks in China. Since then, we have been exported products to the Middle East, South Asia and Africa. Our market is expanding each year and we are looking for more distributors in different countries to be our business partners. Besides electric locks and accessories, we have also developed our own access control system by our software team. The system includes smart card solution and also biometric access control, such as hand-key, fingerprint and facial recognition. Our EC-PAYROLL system has been widely used in many factories both in Hong Kong and mainland China.

After all, GSKA has an objective of "Always Provide the Best" and we shall consistently provide high quality products and reliable services to our worldwide customers. We are looking forward to making good business with our partners